Lockouts · Oxford Park
Break-In Damage Lock Repair in Oxford Park
There is a hole where the cylinder used to be.
In plain words
There are really two jobs inside one call. The first is tonight: make the door close and lock so the household can sleep. Where the door and frame are sound that means a new lockset or cylinder; where the jamb has split it means a repair plate over the break or a board across the opening, always arranged so the door still opens from inside without a key. The second job is the permanent repair, often the same visit: a reinforced strike box, long screws into the stud, a strengthened door edge and a deadbolt with a full throw. Both are quoted separately so you decide what happens when.
How the visit goesThe patio slider is sitting crooked on its track. Its latch is snapped, the frame is bowed where it was pried, and the panel no longer meets the jamb, so the house cannot be closed up for the night.
Break-In Damage Lock Repair
How the visit goes
Does the door still hang true
An impact hard enough to break a strike usually moves the door as well. The locksmith checks that the door sits square in its opening, closes on its weatherstrip without force, and that the bolt lines up with its pocket rather than dragging on the strike lip. Hinge screws are tested for grip, since a kick can pull them from the jamb even on the side that was not attacked, and the hinge leaves are checked for bending. Manufacturers treat strike position, pocket depth and door alignment as working parts of the lock, and a repair that ignores them produces a door that locks badly the day after it was fixed.
Sliding doors and garage entries
A forced patio slider is repaired by putting the panel back on its track, replacing the broken latch or fitting an auxiliary bolt into the frame, and adding the pieces that stop the next attempt: anti-lift blocks in the upper channel so the panel cannot be raised off its rollers, and a foot bolt or pin lock at the bottom. A garage man-door that carried only a knob lock gets a proper deadbolt, a boxed strike and long hinge screws to match the front of the house. Where an overhead door was the way in, the emergency release cord is shielded from outside reach and the opener remotes are reprogrammed.
New keys and a clean slate
If keys were taken, you now hold a set that fits locks nobody else can open. The cylinders were pinned to a fresh combination and the new keys were cut from that pinning, tested in each door and counted into your hand. It is worth deciding on the spot who gets one and where the spare lives, which is no longer a hook by the door. Garage remotes have been erased and re-paired, and you have been reminded to change alarm codes and any code written on paper that was disturbed. The stolen ring is now a handful of metal that turns nothing.
Break-In Damage Lock Repair
In the van
Jamb repair plate
Two-part wood epoxy and shims
Wrap-around door edge reinforcer
Grade 1 deadbolt with one-inch throw
Plywood and cleats for boarding
Break-In Damage Lock Repair
What affects the quote
Keys cut
New keys are cut from the fresh pinning and counted separately: enough for each adult, the dog walker and a trusted neighbour, however many you decide you need.
Method of jamb repair
Bonding a split with epoxy and a repair plate is one line; fitting a new section of wood is another; a full jamb leg through a carpenter is quoted by that trade.
Door and frame material
A wood jamb over a stud takes standard reinforcement. Steel frames, jambs on masonry, fibreglass doors and aluminum storefront stiles each need their own fasteners and methods, which changes both labour and parts.
What to have ready
- Is everyone safe, and is the property clear of anyone who should not be there?
- Is the damage to the lock, the frame, the door edge or the glass, or several?
- Were any keys, garage remotes or alarm codes taken?
Break-In Damage Lock Repair: questions
QuestionsDo longer screws really make a difference?
A large one. Factory strike and hinge screws are usually short enough to grip only the jamb, a piece of trim about an inch thick. Three-inch screws pass through the jamb and the gap behind it into the stud, so a blow has to move the wall rather than the trim. Lock manufacturers supply reinforcement plates with three-inch screws for exactly this reason, and note that a door beside a sidelight needs a different arrangement because glass sits where the stud would be.
Can a split jamb be repaired, or does it need replacing?
Many can be repaired. A split along the grain is pressed back together, glued with a two-part wood epoxy and held by a steel repair plate or a boxed strike screwed through it into the stud, so the fasteners reinforce the repair as well as the lock. Missing wood is built up with filler or a fitted piece. A jamb that has pulled off the framing along its length or shattered around the pocket is replaced by a carpenter, with the opening secured until then.
Will my door be boarded up, or can it be made to lock tonight?
Most forced doors lock again during the visit. If the slab and frame are sound, a new lockset goes in and the strike is reinforced. If the jamb is split, a repair plate or a boxed strike screwed into the stud usually holds it. Boarding is reserved for openings where the frame or the door itself is destroyed, and even then it is fitted so the household can get out from inside without a key.
Related services
- Business Lockout ServiceIt is ten to nine, three staff are on the sidewalk with their coffees, and the key that has opened the glass front door for six years will not turn.
- Broken Key ExtractionThe padlock on the shed has been stiff all summer.
- Seized & Jammed Lock OpeningEvery time you pull the key out of the side door it comes away gritty.