Lockouts · Manor Park
Break-In Damage Lock Repair in Manor Park
There is a hole where the cylinder used to be.
In plain words
When a home is broken into, the locks are not the only thing that has changed hands. Keys hanging in the hall, a spare in a drawer, a garage remote on a visor or a house key on a stolen car's ring may all be gone. Part of break-in damage repair is closing that door too. Every cylinder those keys fit is rekeyed or replaced and fresh keys are cut, the mailbox and padlocks are considered, and you are reminded to reset the garage opener and any alarm codes that were written down. The forced door gets fixed, and the missing keys stop mattering at the same time.
How the visit goesThe patio slider is sitting crooked on its track. Its latch is snapped, the frame is bowed where it was pried, and the panel no longer meets the jamb, so the house cannot be closed up for the night.
Break-In Damage Lock Repair
How the visit goes
The other openings
The attacked door was chosen for a reason, and the locksmith walks the rest of the property to see whether the same reason applies elsewhere. A back door with a knob lock and no deadbolt, a garage man-door on a light latch, a basement walkout hidden from the street, a sliding door with no anti-lift blocks or a side gate that is never locked are all noted. The walk takes a few minutes and lets you decide, with the whole picture in view, whether the repair stops at the forced door or brings the weaker openings up to the same standard while the tools are out.
Securing the opening for the night
Before anything permanent, the door has to close and lock. Where the slab and frame are sound, a new deadbolt or cylinder goes straight in and the job moves on to reinforcement. Where the jamb is split, a steel repair plate is screwed over the break to hold the wood together and give the strike something to bite, or the strike is boxed and screwed into the stud behind the damage. Where the frame or door is too broken for hardware, plywood is fitted across the opening with cleats from inside, arranged so the household can still get out without a key. You know before the locksmith leaves exactly how the door is being held.
New keys and a clean slate
If keys were taken, you now hold a set that fits locks nobody else can open. The cylinders were pinned to a fresh combination and the new keys were cut from that pinning, tested in each door and counted into your hand. It is worth deciding on the spot who gets one and where the spare lives, which is no longer a hook by the door. Garage remotes have been erased and re-paired, and you have been reminded to change alarm codes and any code written on paper that was disturbed. The stolen ring is now a handful of metal that turns nothing.
Break-In Damage Lock Repair
In the van
Jamb repair plate
Two-part wood epoxy and shims
Wrap-around door edge reinforcer
Grade 1 deadbolt with one-inch throw
Plywood and cleats for boarding
Break-In Damage Lock Repair
What affects the quote
Commercial and storefront hardware
Narrow-stile deadbolts, hookbolts, latch guards, anti-pry astragals and interchangeable cores are commercial parts with commercial fitting time, and a shop's quote reflects them.
Sliding door hardware
Putting a slider back on its track, replacing its latch and adding anti-lift blocks, a foot bolt or an auxiliary lock is a different parts list from a hinged door, and is quoted as such.
Number of cylinders rekeyed
Every lock a taken key fits is rekeyed individually, so a house with four exterior doors, a mailbox and two padlocks is more work than one front door. Bringing them all onto a single key is part of the count.
What to have ready
- Is the damage to the lock, the frame, the door edge or the glass, or several?
- Were any keys, garage remotes or alarm codes taken?
- Have the police been called, and do you have an occurrence number?
Break-In Damage Lock Repair: questions
QuestionsDo longer screws really make a difference?
A large one. Factory strike and hinge screws are usually short enough to grip only the jamb, a piece of trim about an inch thick. Three-inch screws pass through the jamb and the gap behind it into the stud, so a blow has to move the wall rather than the trim. Lock manufacturers supply reinforcement plates with three-inch screws for exactly this reason, and note that a door beside a sidelight needs a different arrangement because glass sits where the stud would be.
Can a split jamb be repaired, or does it need replacing?
Many can be repaired. A split along the grain is pressed back together, glued with a two-part wood epoxy and held by a steel repair plate or a boxed strike screwed through it into the stud, so the fasteners reinforce the repair as well as the lock. Missing wood is built up with filler or a fitted piece. A jamb that has pulled off the framing along its length or shattered around the pocket is replaced by a carpenter, with the opening secured until then.
Will my door be boarded up, or can it be made to lock tonight?
Most forced doors lock again during the visit. If the slab and frame are sound, a new lockset goes in and the strike is reinforced. If the jamb is split, a repair plate or a boxed strike screwed into the stud usually holds it. Boarding is reserved for openings where the frame or the door itself is destroyed, and even then it is fitted so the household can get out from inside without a key.
Related services
- Business Lockout ServiceIt is ten to nine, three staff are on the sidewalk with their coffees, and the key that has opened the glass front door for six years will not turn.
- Broken Key ExtractionThe padlock on the shed has been stiff all summer.
- Seized & Jammed Lock OpeningEvery time you pull the key out of the side door it comes away gritty.