Car keys · London
Ignition Lock Repair
Turning the key used to take one smooth motion.
In plain words
A key that has snapped off inside the ignition barrel is not the end of the key, or of the barrel. The broken piece is drawn out with hooked or spiral tools built for the job, without pushing it further in, and the cylinder is checked afterward for the wear that likely caused the break in the first place. A fresh key is then cut and tested before the visit ends.
How the visit goesThe car arrived with one worn-looking key and a story about a lost spare. It turns the ignition, eventually, after some patience and a particular angle nobody in the household can quite describe or repeat on the first try.
Ignition Lock Repair
How the visit goes
Reading the exact symptom
The next question is about behaviour, not diagnosis. Does the key insert at all? Does it turn partway, all the way, or not at all? Does it turn without the steering lock releasing, or without the dash lighting up? Is it stuck, unable to come back out once the engine is off? Each answer points somewhere different inside the mechanism, and a locksmith who hears the exact sequence before arriving brings the right decoders, extraction tools and replacement parts rather than guessing from a general description that the key just does not work.
Removing a broken key without losing more of it
A snapped key calls for patience rather than force. Hooked and spiral extractors reach into the barrel and draw the broken piece out along the same path it went in, rather than pushing it deeper or twisting it further. Once the fragment is clear, the cylinder is tested and examined for the wear that likely caused the break, and a freshly cut key replaces the two broken halves before the vehicle is handed back to its owner.
A cylinder and key with a clean history behind them
Where the ignition showed signs of an earlier forced attempt, the replacement hardware carries none of that history forward: new pins, a new key, and a housing that has not been tampered with. You are shown the old part before it is handed over or taken away, so the vehicle's ignition starts its next chapter with hardware nobody has already tried once to defeat.
Ignition Lock Repair
In the van
Ignition lock cylinder
Trim clips and fasteners
Broken key extractors
Pick and tension tools
Steering column trim tools
Ignition Lock Repair
What affects the quote
Aftermarket wiring near the ignition
A remote starter, an alarm, or other aftermarket wiring tied into the column changes what the locksmith has to work around and identify correctly before the mechanical repair can proceed safely.
Keying other locks to match
Bringing the doors and trunk onto a newly pinned ignition key, so one key runs the whole vehicle again, is separate work from the ignition repair itself, even when it happens during the same visit.
Weather and road conditions on the day
A barrel packed with road salt, grit or old grease from a rough season takes longer to clean and free than one that has simply worn with ordinary use over the years of driving.
What to have ready
- Do you have a spare or second key available?
- Are any warning or immobilizer lights showing on the dash?
- Do you have the vehicle permit or proof of ownership handy?
Ignition Lock Repair: questions
QuestionsCan the repaired ignition still be operated by my existing key?
In most cases, yes. Whether the cylinder is serviced in place or replaced outright, it is pinned to match the key you already carry wherever the vehicle's design allows it, rather than handing you a second key to keep track of. If the vehicle's own hardware makes that impossible, you are told before any work begins, not afterward.
I just bought a used vehicle with one worn key. What should I expect?
A single worn key is a common starting point after buying used, and the visit usually has two parts: reading the existing wafers so a crisp new key can be cut, and deciding whether the barrel itself needs a service given whatever wear the previous owner's key left behind. Bringing whatever paperwork came with the sale helps confirm ownership before any work begins.
Do you check the steering lock as part of this service?
Yes. The steering lock is mechanically tied to the ignition barrel on most vehicles, engaging when the key is removed and releasing as the key turns toward accessory. It is cycled several times during testing, alongside every switch position, so a fault that shows up only in how the wheel locks or releases does not go unnoticed after the visit is finished.
Related services
- Car Key ReplacementThe key snapped at the head while you were turning it in a stiff, frosty door lock.
- Spare Car Key DuplicationA teenager just passed a driving test and reasonably wants a key of their own rather than negotiating over the family's single copy every time the car is needed.
- Key Fob ProgrammingA fob went missing weeks ago somewhere between a coat pocket and a parking lot, and a spare has covered the gap since.